Effects of upholstery materials on the burning behavior of real‐scale residential upholstered furniture mock‐ups

Fire spread and growth on real‐scale four cushion mock‐ups of residential upholstered furniture (RUF) were investigated with the goal of identifying whether changes in five classes of materials (barrier, flexible polyurethane foam, polyester fiber wrap, upholstery fabric, and sewing thread), referred to as factors, resulted in statistically significant changes in burning behavior. A fractional factorial experimental design plus practical considerations yielded a test matrix with 20 material combinations. Experiments were repeated a minimum of two times. Measurements included fire spread rates derived from video recordings and heat release rates (HRRs). A total of 13 experimental parameters (3 based on the videos and 10 on the HRR results), referred to as responses, characterized the measurements. Statistical analyses based on Main Effects Plots (main effects) and Block Plots (main effects and factor interactions) were used. The results showed that three of the factors resulted in statistically significant effects on varying numbers of the 13 responses. The Barrier and Fabric factors had the strongest main effects with roughly comparable magnitudes. Foam was statistically significant for fewer of the responses and its overall strength was weaker than for Barrier and Fabric. No statistically significant main effects were identified for Wrap or Thread. Multiple two‐term interactions between factors were identified as being statistically significant. The Barrier*Fabric interaction resulted in the highest number of and strongest statistically significant effects. The existence of two‐term interactions means that it will be necessary to consider their effects in approaches designed to predict the burning behavior of RUF.     

工艺参数对动态流量控制法挤压弯管应力的影响

采用有限元模拟和实验研究了挤压钛合金弯曲管件。通过实验验证了工件的形状和尺寸精度,并通过有限元模拟分析了工艺参数对挤出过程中变形体的平均压应力分布情况和挤出弯管件的曲率半径的影响规律。结果表明:有限元模拟中,弯管件的曲率半径误差为6.03%,弯管直径误差为3.82%;在靠近定径带处,平均压应力呈非均匀分布;在焊合腔内,靠近细分流孔区域的平均压应力小于靠近粗分流孔区域的平均压应力,平均压应力的大小顺序在通过粗、细分流孔前后相反;在模具结构固定不变时,弯管件的曲率半径随挤压速度的减小而增大,不随挤压温度的变化而变化。     

Reduced‐scale test to assess the effect of fire barriers on the flaming combustion of cored composites: An upholstery‐material case study

Herein, we describe a reduced‐scale test (“Cube” test), measuring the fire performance of specimens including a fire barrier (FB) and a flammable core material, which acts as the main fuel load. The specimen is intended to reproduce a cross‐section of a composite product where heat/mass transfer occurs primarily in a direction perpendicular to the FB. The Cube test procedure and benefits are discussed in this work by adopting residential upholstery furniture as an exemplary study. One flexible polyurethane foam, one polypropylene cover fabric, and 10 commercially available FBs were selected. They were used to compare the fire performance of FBs, measured in terms of peak of heat release rate, in the ASTM E1474‐14 standard test and the newly developed Cube test. Edge effects severely affected the performance of FBs in the ASTM E1474‐14 standard test but not in the Cube test. Furthermore, appropriate test conditions were determined in the Cube test to measure the so‐called “wetting point,” that is, the time and value of heat release rate measured when flammable liquid products were first observed on the bottom of the specimen. The relevance of the “wetting point” in terms of full‐scale fire performance and failure mechanism of FBs is discussed.     

往复活塞式压缩机活塞杆温度高故障分析及改造

针对2台2D40型空气压缩机在实际试机过程中,活塞杆温度过高,导致连锁报警,压缩机不能正常工作的问题进行了详细的故障原因分析;对压缩机技术性能参数进行介绍;对压缩机的损伤情况进行说明并找到改造方案,解决机组运行中活塞杆温度过高的问题,从而提高机组的运行效率,使机组运行安全、稳定。     

Performance enhancement of methanol reforming reactor through finned surfaces and diffused entry for on-board hydrogen generation

Hydrogen-rich combustion in engines helps in reducing pollutants significantly. But hydrogen usage on a moving vehicle is not getting large-scale user acceptance mainly due to its poor energy storage density resulting in shorter driving ranges. This storage issue led to the hunt for mediums that can efficiently produce on-board hydrogen. Methanol proves to be an efficient alcohol fuel for producing hydrogen through steam reforming reaction. The heat energy required for such endothermic reaction is obtained through exhaust engine waste energy and this process is collectively known as thermochemical recuperation. However, the conventional reactor used for this process faces a lot of problems in terms of efficiency and methanol conversion. In this study, an attempt has been made to improve the design of the reactor for on-board hydrogen generation using engine exhaust heat for addressing the challenges related to performance and hydrogen yield. For enhancing the heat transfer, a finned surface (straight & wavy) was introduced in the reactor which resulted in an increment in methanol conversion significantly. It was found that wavy fin improved the methanol conversion up to 96.8% at an exhaust inlet temperature of 673 K. Also, a diffusing inlet section was introduced to increase the residence time of reactant gases while passing through the catalyst zone. Under given inlet conditions, the methanol conversion for 6° diffuse inlet reactor goes up to 87.9% as compared to 75.4% for the conventional reactor.     

Effect of heat transfer through the release pipe on simulations of cryogenic hydrogen jet fires and hazard distances

Jet flames originated by cryo-compressed ignited hydrogen releases can cause life-threatening conditions in their surroundings. Validated models are needed to accurately predict thermal hazards from a jet fire. Numerical simulations of cryogenic hydrogen flow in the release pipe are performed to assess the effect of heat transfer through the pipe walls on jet parameters. Notional nozzle exit diameter is calculated based on the simulated real nozzle parameters and used in CFD simulations as a boundary condition to model jet fires. The CFD model was previously validated against experiments with vertical cryogenic hydrogen jet fires with release pressures up to 0.5 MPa (abs), release diameter 1.25 mm and temperatures as low as 50 K. This study validates the CFD model in a wider domain of experimental release conditions - horizontal cryogenic jets at exhaust pipe temperature 80 K, pressure up to 2 MPa ab and release diameters up to 4 mm. Simulation results are compared against such experimentally measured parameters as hydrogen mass flow rate, flame length and radiative heat flux at different locations from the jet fire. The CFD model reproduces experiments with reasonable for engineering applications accuracy. Jet fire hazard distances established using three different criteria - temperature, thermal radiation and thermal dose - are compared and discussed based on CFD simulation results.     

Experimental and numerical study on tube-side flow and heat transfer characteristics of superheated vapor flow in catalyst-filled LH2 spiral wound heat exchanger

High energy consumption is considered to be one of the most persistent problems in liquid hydrogen (LH₂) plants. The combination of heat exchanger and ortho-para (O–P) hydrogen conversion has attracted considerable attention as a cutting-edge technology to reduce energy consumption. The flow and heat transfer characteristics of O–P hydrogen conversion catalyst-filled spiral wound heat exchanger (SWHE) were investigated in this study in two steps. In the first step, pressure-drop experiments were performed in a tube filled with porous media. The results indicated that the pressure drop was overestimated when using Ergun's equation. Therefore, a new empirical pressure-drop correlation for a channel filled with O–P catalyst was formulated. Subsequently, a novel heat transfer model was established based on this correlation for further numerical simulations. The distributions of the temperature, pressure, and para hydrogen content in a catalyst-filled tube were determined. In addition, the influence of the flow rate on the heat exchange coefficient and outlet para hydrogen was clarified; it was found that, with an increase in the flow rate, the heat exchange coefficient increased, whereas the outlet para hydrogen content decreased. At a flow rate of 0.5 m³/h, the para hydrogen content increased by 44% after hydrogen flowed through the channel filled with the O–P catalyst. Furthermore, a prediction model for the para hydrogen content with a flow rate range of 0–1.5 m³/h was derived. This study provides promising theoretical evidence for the engineering application of SWHEs filled with O–P catalysts in large-scale hydrogen liquefaction units.     

Effects of ultrafiltration combined with high-pressure processing,ultrasound and heat treatments on the quality of a blueberry–grape–pineapple–cantaloupe juice blend

This study investigated the effect of ultrafiltration (UF) combined with high-pressure processing (HPP) at 550 MPa, 25 °C for 5 min, ultrasound (US) at 520 W, 40 °C for 10 min and heat treatment (HT) at 90 °C for 3 min on the microbial, physicochemical and sensory properties of a blueberry–grape–pineapple–cantaloupe juice blend during 104 days of storage at 4 °C. After UF, the shelf life of the HPP- and US-treated clear juice blends were 104 and 72 days during the storage at 4 °C respectively. HPP, US and HT treatment minimally affected the anthocyanin and total phenol contents, while HPP better maintained the ascorbic acid levels and sensory properties in the clear juice blend during the storage. Therefore, HPP combined with UF was identified as a prospective processing technique in the fruit juice industry.     

Analysis of pressure and heat distribution in a dilating or contracting filter chamber with two outlets using multivariate spectral quasilinearization method

The development of efficient filters is an essential part of industrial machinery design, specifically to increase the lifespan of a machine. In the filter chamber design considered in this study, the magnetic material is placed along the horizontal surface of the filter chamber. The inside of the filter chamber is layered with a porous material to restrict the outflow of unwanted particles. This study aims to investigate the flow, pressure, and heat distribution in a dilating or contracting filter chamber with two outlets driven by injection through a permeable surface. The proposed model of the fluid dynamics within the filter chamber follows the conservation equations in the form of partial differential equations. The model equations are further reduced to a steady case through Lie's symmetry group of transformation. They are then solved using a multivariate spectral-based quasilinearization method on the Chebyshev–Gauss–Lobatto nodes. Insights and analyses of the thermophysical parameters that drive optimal outflow during the filtration process are provided through the graphs of the numerical solutions of the differential equations. We find, among other results, that expansion of the filter chamber leads to an overall decrease in internal pressure and an increase in heat distribution inside the filter chamber. The results also show that shrinking the filter chamber increases the internal momentum inside the filter, which leads to more outflow of filtrates.     

Hall current effects on MHD flow of chemically reacting fluid through a porous medium with heat source

We considered the magnetohydrodynamic (MHD) free convective flow of an incompressible electrically conducting viscous fluid past an infinite vertical permeable porous plate with a uniform transverse magnetic field, heat source and chemical reaction in a rotating frame taking Hall current effects into account. The momentum equations for the fluid flow during absorbent medium are controlled by the Brinkman model. Through the undisturbed state, both the plate and fluid are in a rigid body rotation by the uniform angular velocity perpendicular to an infinite vertical plate. The perpendicular surface is subject to the homogeneous invariable suction at a right angle to it and the heat on the surface varies about a non-zero unvarying average whereas the warmth of complimentary flow is invariable. The systematic solutions of the velocity, temperature, and concentration distributions are acquired systematically by utilizing the perturbation method. The velocity expressions consist of steady-state and fluctuating situations. It is revealed that the steady part of the velocity field has a three-layer characteristic while the oscillatory part of the fluid field exhibits a multi-layer characteristic. The influence of various governing flow parameters on the velocity, temperature, and concentration are analyzed graphically. We also discuss computational results for the skin friction, Nusselt number, and Sherwood number in the tabular forms.